View EM32117Q_1236922.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

EM32117
16DIGITLCDDRIVERWITHCHECKTIMEFUNCTION
in Prelim
GENERAL DESCRIPTION
ary
EM32117 is a CMOS 16-digit LCD panel driver. The EM32117 can receive dialing information such as dialing digits, Pause, Flash, Pulse to Tone mode from EMC EM91465 series dialer IC and display the corresponding pattern on the LCD panel. The EM32117 also supports various indicators such as the icons of STORE, SAVE, Speaker phone (or Hand-Free), Lower or Upper page, Hold, etc. to support high-end feature phone applications. The EM32117 can operate in stand-alone mode to display calendar and real time clock, conversation time (stopwatch). The EM32117 also provides check the last conversation time function.
FEATURES
* * * * * * * * * * * * ON-HOOK check last conversation time function. General flag display function for LOGO indication. Low power consumption: 1.5A (max.) Uses single clock 32768 Hz crystal (with built-in capacitor, no need extra capacitor). LCD blank 2 sec after OFF-HOOK, to protect the STW data. Built-in serial data interface (compatiable with EM91465 series). Driver for 4.5-volt, 16-digit, 1/4 duty , 1/3 bias LCD panel with built-in voltage tripler circuit. Display dialing phone number. Display calendar and real time clock (RTC) in 12 hour or 24 hour format. Stopwatch function for counting conversation time up to 59 minutes 59 seconds. Operating voltage: 1.5 VDC ( typical ) Dice form, QFP 80 pin package, and LCM (Liquid Crystal display Module) are available.
APPLICATION
* LCD Feature phone and Digital display system.
PIN ASSIGMENT
NC NC NC NC NC NC SEG26 SEG27 SEG28 SEG29 SEG30 SEG31 COM0 COM1 COM2 COM3 ENCLND* ENRTC* 24/12* NC NC NC NC NC 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
SEG25 SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10
65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
EM32117Q
40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25
XOUT XIN VSS VC2 VC1 V3 V2 VDD HKS SD1 MS2 MS1 SPARE1 SPARE2 NC NC
* This specification are subject to be changed without notice.
NC NC NC NC NC NC NC SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 SEG0 GF TEST NC NC NC NC NC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
3.17.1999
1
EM32117
16DIGITLCDDRIVERWITHCHECKTIMEFUNCTION
FUNCTION BLOCK DIAGRAM
COM0~3
ina relim P
SEG0~31
ry
1/4 Duty 1/3 bias LCD Driver
Serial Data Sampling & Decoding Serial Data Display Buffer RTC/STW Counter
GF
SD1
Sampling Signal Generator
XIN XOUT
OSC
Timing & Control Circuit
VDD VSS
Power Supply Circuit
ENCLND ENRTC 24/12 HKS MS2 MS1 TEST
PIN DESCRIPTION
Pin Name SPARE1, SPARE2 COM0~COM3 SEG0~SEG31 TEST MS1 Description Need to be connected to VSS. LCD panel driver common output pins. LCD panel driver segment output pins. Reserved for testing, should be left open. Manual setting and check last conversation time input pin 1, with built-in pull-up optimal resistor. The optimal resistor before keying=100k, after keying change to 1M for reducing power consumption. Manual setting input pin 2 with built-in pull-up; optimal resistor. The optimal resistor before keying=100k, after keying change to 1M for reducing power consumption. Serial data input pin with built-in 150 K pull-up resistor. Hook switch status input pin with built-in 1 M pull-up resistor. Positive power supply pin. Voltage tripler circuit for LCD driver. Voltage tripler circuit for LCD driver. Crystal input and output pins for connecting a 32768Hz crystal (Internal built-in 2-p capacitor). RTC display 24 or 12 hours format selection pin (when this pin is pulled "high, RTC will be displayed in 24 hour format. Otherwise will be display in 12 hour format). Calendar enable pin. When disabled (ENCLND* = high), the Calendar field of LCD panel will be blanked. When 12 digit LCD panels are used, Calendar should be disable to suppress output of calendar. RTC enable pin. When disabled (ENRTC* = high), the LCD panel will be blanked when HKS pin is at high level. General Flag input pin without built-in resistor. When GF pull "High" LCD panel will display Icon. GF pull "Low", "GF" Icon will blank. 3.17.1999
2
MS2
SDI HKS VDD, VSS V2, V3 VC1, VC2 XIN, XOUT 24/12 ENCLND
ENRTC GF
* This specification are subject to be changed without notice.
EM32117
16DIGITLCDDRIVERWITHCHECKTIMEFUNCTION
in Prelim
LCD Panel Description
ary
The display font of the EM32117 LCD driver is shown as the following:
Digit #
16
RD
15
SPEAKER
14
HOLD
13
12
MEMORY
11
10
9
ALARM
8
STORE
7
PAGE
6
5
AUTO
4
LOCK
3
SAVE
2
1
MUTE
LO BATT
BLANK
1
2
3
4
5
6
7
8
9
0
*
#
PAUSE TONE DASH
COM3 COM2 COM1 COM0
SEG31 16f 16g 16e 16d SEG23 12f 12g 12e 12d SEG15 8f 8g 8e 8d SEG7 4f 4g 4e 4d
SEG30 16a 16b 16c
SEG29 15f 15g 15e 15d SEG21 11f 11g 11e 11d SEG13 7f 7g 7e 7d SEG5 3f 3g 3e 3d
SEG28 15a 15b 15c
SEG27 14f 14g 14e 14d SEG19 10f 10g 10e 10d SEG11 6f 6g 6e 6d SEG3 2f 2g 2e 2d
SEG26 14a 14b 14c
SEG25 13f 13g 13e 13d SEG17 9f 9g 9e 9d SEG9 5f 5g 5e 5d SEG1 1f 1g 1e 1d
SEG24 13a 13b 13c
COM3 COM2 COM1 COM0
SEG22 12a 12b 12c RD SEG14 8a 8b 8c GF SEG6 4a 4b 4c AUTO
SEG20 11a 11b 11c Speaker SEG12 7a 7b 7c ALARM SEG4 3a 3b 3c LOCK
SEG18 10a 1b 10c HOLD SEG10 6a 6b 6c STORE SEG2 2a 2b 2c SAVE
SEG16 9a 9b 9c Memory SEG8 5a 5b 5c PAGE SEG0 1a 1b 1c MUTE
COM3 COM2 COM1 COM0
COM3 COM2 COM1 COM0
RD
COM3 COM2 COM1 COM0
SPEAKER
HOLD
MEMORY
GF
ALARM
STORE
PAGE
AUTO
LOCK
SAVE
MUTE
* This specification are subject to be changed without notice.
3.17.1999
3
EM32117
16DIGITLCDDRIVERWITHCHECKTIMEFUNCTION
ina relim P
RD SPEAKER HOLD MEMORY
ry
GF
ALARM
STORE
PAGE AUTO LOCK
SAVE
MUTE
SEG31
SEG29
SEG27 SEG25
SEG23 SEG21
SEG19 SEG17 SEG15
SEG13 SEG11
SEG9
SEG7
SEG5
SEG3
SEG1 SEG0
SEG30
SEG28
SEG26 SEG24
SEG22 SEG20
SEG18 SEG16 SEG14
SEG12 SEG10
SEG8
SEG6
SEG4
SEG2
Figure 2 - Segment pin wiring diagram Serial Data Interface Since the serial data transmitters (e.g. EM91465 series dialers) may have different voltage level from EM32117, therefore the following interconnecting scheme is recommended when using the EM32117 as a serial data receiver. The SDO output from the serial data transmitters should be of NMOS open-drain structure as shown below. VCC
Dialer EM32117 5 SDO SDI Vss 6 4 5 6 4 1 1 2 2 3 3
Vss
Vss
Data Format When the EM32117 senses the falling edge of the Start bit, it will sample subsequent bits in the middle of each bit. The received bit will then be assembled and decoded, and corresponding pattern will be displayed on LCD panel. The serial data format is as follows:
0
1 Start Bit
Bit 0
Bit 1
Bit 2 Data Bits
Bit 3
Bit 4
Bit 5
0 Stop Bit
1
Protocol There are three categories of dialing data, and representation and interpretation of serial data is as the following: (Note: Codes 0000 and 1111 will be interpreted as" " (blank pattern) and"-"patterns, respectively and they will shift on LCD panel just as other digit codes.
* This specification are subject to be changed without notice.
3.17.1999
4
EM32117
16DIGITLCDDRIVERWITHCHECKTIMEFUNCTION
in Prelim
Keypad,SDO format and LCD display reference table:
ary
Keypad bit5 bit4 bit3 bit2 bit1 bit0 Display 1 0 0 0 0 0 1 1 2 0 0 0 0 1 0 2 3 0 0 0 0 1 1 3 4 0 0 0 1 0 0 4 5 0 0 0 1 0 1 5 6 0 0 0 1 1 0 6 7 0 0 0 1 1 1 7 8 0 0 1 0 0 0 8 9 0 0 1 0 0 1 9 0 0 0 1 0 1 0 0 "*"/T 0 0 1 0 1 1 # 0 0 1 1 0 0 P 0 0 1 1 0 1 P */"T" 0 0 1 1 1 0 ST 1 0 0 0 0 0 STORE HOLD 1 0 1 0 0 0 HOLD HF 1 0 1 0 1 0 Speaker Page 1 0 1 1 0 0 PAGE A 1 0 1 1 1 0 A F 1 0 1 1 1 1 clear all display (Lock state) 1 0 0 0 0 1 Lock MUTE 1 0 0 0 1 0 MUTE Note 3 1 0 0 0 1 1 ALARM EM1~EM3 1 1 1 1 0 0 MEMORY M1~M40 1 1 1 1 0 0 MEMORY RD 1 1 1 1 0 1 RD SAVE 1 1 1 1 1 0 SAVE Note: 1. Flash key will be treated as "clear LCD panel" command. 2. When lock condition establish. 3. MUTE and ALARM indicators will toggle with each received SDI code. 4. Any invalid data will be ignored by the EM32117. * General flag display function. EM32117 provide General Flag Icon, when GF pin pull "high", then "GF" Icon will be displayed. GF pin pull "low", the "GF" Icon will blank. The "GF" Icon can identify by user for special distinguishment.
FUNCTION DESCRIPTION
Operation Modes and System States Depending on which state the EM32117 is in, the system will operate in one of two modes, namely, RTC mode and Stop-watch mode. In the State 1, as defined by the State-diagram in figure 4, the system operates in RealTime Clock mode, otherwise, the system operates in Stop-Watch mode. The flow chart is as follows:
* This specification are subject to be changed without notice.
3.17.1999
5
EM32117
16DIGITLCDDRIVERWITHCHECKTIMEFUNCTION
ina relim P
1 RTC Mode State>1 State=1
ry
2
Stop watch Mode
Figure 3 - Top Level Flow Chart The system can be in one of the six states as defined by the following state diagram. The transitions between states are driven by the level of HKS pins as well as Serial Data "Hand-Free" and "Hold".
1 HF HF On-hook state HKS=Lo HKS=Hi
4 HKS=Lo On-hook Hand-free state
2
Off-hook state
HKS=Hi HD HF
3 Off-Hook Hand-free state
HF HF HD HD
HD
6 HD ON-Hook Hold-line state HKS=Hi
HF
5 Off-Hook Hold-line state
HKS=Lo
Figure 4 - System State Diagram RTC (Real time clock) Mode When the system is in State 1 and RTC function is enabled (ENRTC pin at low level), the EM32117 will be in Real-Time Clock display mode. There are two different RTC display formats available, e.g., 12 or 24 hours format selected by 24/12 pin. When this pin is pulled "high", RTC will be displayed in 24 hour format. When "low", RTC will be displayed in 12 hour format, as shown in the following: 12 hour format:
24 hour format:
* This specification are subject to be changed without notice.
3.17.1999
6
EM32117
16DIGITLCDDRIVERWITHCHECKTIMEFUNCTION
in Prelim
Setting Calendar and Real-Time clock
ary
When the system is in State 1(ON-HOOK idle state), the calendar and Real-Time Clock can be set up by operating MS1 and MS2 pins as described in the following: 1. When the system is in State 1, press MS1 and hold for over 2 sec , month digits will flash, 2. Press MS2 to increment month digits. 3. Press MS1 once again, day digits will flash, 4. Press MS2 to increment day digits. 5. Press MS1 again, hour digits will flash. 6. Press MS2 to count up data. 7. Press MS1 once again, minute digits and flash, 8. Press MS2 to count up minute digits. 9. Press MS1 again to finish RTC set up, and the second digit will be reset. Note: 1. If MS2 are pressed and hold for over 2 seconds, then data automatically count up in every 0.5 sec. 2. Digit flash time is 1 Hz (0.5 sec on, 0.5 sec off) The flow chart of RTC mode is as follows:
* This specification are subject to be changed without notice.
3.17.1999
7
EM32117
16DIGITLCDDRIVERWITHCHECKTIMEFUNCTION
ina relim P
RTC_MODE RTC_Display
ry
T
State>1? F MS1=Lo? F
MS1=Lo >2sec? T Month flash F
F N
display last conversation time for 6 sec F
6 sec expired?
RTC_mode Y
T
State>1? F F T
MS1=Lo?
MS2=Lo?
Month+1
T Day Flash F State>1? F F MS1=Lo? T Hour flash F State>1? F MS1=Lo? T Minute Flash F MS2=Lo? T Hour+1 MS2=Lo? T Day+1
State>1? F MS1=Lo? T F
F
T MS2=Lo? Minute+1
STW_MODE
Figure 5 - RTC Flow Chart * This specification are subject to be changed without notice. 3.17.1999
8
EM32117
16DIGITLCDDRIVERWITHCHECKTIMEFUNCTION
in Prelim
Check last conversation time
ary
When the system is at RTC mode, pressed MS1 less than 2 sec. The last conversation will show up on LCD screen to check the last conversation time. Stop Watch mode When the system exits from State 1 (RTC mode), it will enter Stop-watch mode which is intended to count elapsed telephone conversation time up to 59 minutes and 59 seconds and display dialing information such as dialing number, various indicators (MEMORY, RD, HOLD, Hand-Free, etc.) For example: * Originally the system is in State 1, and the LCD panel is in RTC display mode.
* When the HKS pin goes from "high" to "low". The LCD will be blanked.
* After 2 sec, the system switches from State 1 to State 2, the stop watch will start counting from 00-00.
* After 59 minutes and 59 seconds, the stop-watch becomes 59-59.
* Then stop-watch will wrap around and start from 00-00 again.
* This specification are subject to be changed without notice.
3.17.1999
9
EM32117
16DIGITLCDDRIVERWITHCHECKTIMEFUNCTION
ina relim P
ry
Stop-Watch reset and RTC display in Stop-watch Mode The system will enter Stop-watch mode with stop watch automatically reset when the system first switches from State 1 to other States in the Stop-watch mode. In addition, the stop-watch can be reset any time, e.g. when the called party answers, by pressing MS2 switch. For example: * 21 seconds after the system enters Stop-watch mode, the display becomes 00-21.
* When the other party answers, press MS2 key to reset the stop-watch. Then the stop-watch can reflect the real phone conversation time. * When the system is in Stop-watch mode, the EM32117 can be switched to RTC display by pressing MS1.
Dialing Number Display When the system is in Stop-watch mode, each dialing digit data received from SDI pin of EM32117 will be decoded and appears at the right most digit on LCD panel and shifts left as each subsequent digit received until it is shifted out the panel at the left end. If no valid serial data is received for more than 6 seconds, the system will revert to stop watch display until a new digit are received from SDI pin. Display format is as follows: * After HKS pin goes low, the EM32117 will enter Stop-watch Mode, after 2 sec blanking state.
* When "035" are received from SDI pin, the EM32117 will switch to dialing number display.
* After "787" are received, the LCD panel is as shown below: * This specification are subject to be changed without notice. 3.17.1999
10
EM32117
16DIGITLCDDRIVERWITHCHECKTIMEFUNCTION
in Prelim
ary
* Then "505" are received.
* Then "21912345" are received, the display is as follows:
* 6 seconds after the last received digit, the EM32117 will go back to stop watch display. .
* When the system reverts to State 1 with ENRTC* at low level, the Stop-watch will stop counting and stay on the panel for 6 more seconds before it switches to RTC display. However, if ENRTC*is at high level when the system returns to State 1, the LCD panel will go blank immediately. Please refer to the following flow chart for detailed information. Stop watch delay : The last conversation time will prevent to be destroyed by stop watch delay function. After off-hook (or turn on HF), STW will be displayed after 2 sec. This function is to prevent the user quickly ON-OFF HOOK to destroy the last conversation time data.
* This specification are subject to be changed without notice.
3.17.1999
11
EM32117
16DIGITLCDDRIVERWITHCHECKTIMEFUNCTION
ina relim P
STW-MODE
ry
LCD BLANK
Reset STW T STW Display T State = 1? F F Data In? T T Start Timer State >1? F F
6 Sec. Expire?
T RTC-MODE Data Valid? F
MS2 = 0? T F Display Dialing No. Start Timer T Display RTC State = 1? T State = 1? F Data in? F F RTC-MODE T F Data Valid? T F Data In? T F MS1 = 0? Data Valid? F T T F
6 Sec. Expire?
MS1 = 0
T RTC-MODE T
Figure 6 - Stop-watch mode flow chart * This specification are subject to be changed without notice. 3.17.1999
12
EM32117
16DIGITLCDDRIVERWITHCHECKTIMEFUNCTION
in Prelim
Displaying Indicators
ary
When the received serial data correspond to indicators, depending on which group the indicators belong to, the responses to the data are different. * If the contents of the data corresponds to either one of the SPEAKER, HOLD indicators, then the states of the indicators are governed by the state diagram in figure 4. As the state-diagram suggests, the indicators HOLD and SPEAKER are controlled by the status of HKS pin as well as Serial Data HOLD, and SPEAKER. Operating state 1. On-hook state 2. Off-hook state 3. Off-hook, HF state 4. On-hook, HF state 5. Off-hook, HD state 6. On-hook, HD state HKS pin status Hi Lo Lo Hi Lo Hi HOLD Indicator OFF OFF OFF OFF ON ON SPEAKER Indicator OFF OFF ON ON OFF OFF
* If the Serial Data received corresponds to one of Redial, Store, Auto, Page, Memory indicators for the first time after HKS pin switches from high to low, it will be interpreted as "turning-on the indicator". These indicators will remain on till 6 seconds after the last dialed number when the display mode switches from Dialing Number Display to Stop-watch display, then these indicators will go out. * If the received Serial Data corresponds to the codes of MUTE or ALARM, then each receptions of the same serial data will be interpreted as "flipping (toggling) the current state of the indicator". However, when the system returns to state 1, the MUTE will also be cleared.
Driving a 12 digit LCD panel When the EM32117 is driving a 12 digit LCD panel, the ENCNLD should be pulled to VDD to suppress the display of calendar. For example, * When the system is in State 1 (the LCD panel is at RTC mode), pulling ENCNLD to VDD will disable display of calendar.
Note: Calendar display will be automatically suppressed when Real-Time Clock is disable (pulling ENRTC to high level). Suppressing Real-Time Clock Display With the ENRTC at high level (Real-Time Clock disabled) and the system is in State 1, the LCD panel will be blanked. While the system is in Stop-watch mode, it is not possible to switch to calendar and RTC mode by pressing MS1 key. * This specification are subject to be changed without notice. 3.17.1999
13
EM32117
16DIGITLCDDRIVERWITHCHECKTIMEFUNCTION
ina relim P
ABSOLUTE MAXIMUM RATINGS
Items Supply voltage Input voltage Output voltage Power dissipation Operating temperature Storage temperature Sym. V DD V IN VO PD T OPR TSTR
ry
Condition
Rating - 0.5V to 5V - 0.5V to VDD + 0.5V - 0.5V to VDD+0.5V -0.5 V to 5V 300 mW 0oC to 50oC -55oC to 125oC
Except open-drain Open-drain Topr = 50oC
RECOMMENDED OPERATING CONDITIONS
1. Supply voltage at 1.5 V D.C. 2. Operation frequency fosc: 32768 Hz 3. Crystal don't need extra capacitor
DC AND AC ELECTRICAL CHARACTERISTICS (fosc=32768 Hz; VSS = 1.50V)
Parameter Operatingvoltage Sym. V DD V2 V3 Idd ViH ViL RoiH RoiL Ri fosc. Tstart ViH ViL Tdb Min. 1.2 2VDD-0.1 3VDD-0.15 VDD-0.3 V SS VDD - 0.2V V SS Typ. Max. Unit V V A V V M K K Hz Sec. V V mS Condition 1.5 1.6 2V DD 2VDD+0.1 3V DD 3VDD+0.15 1 1.5 1 100 150 32768 20 V DD VSS + 0.3 2 V DD VSS + 0.2 -
Operating current (no load) Input voltage (Input pins except HKS) Input pins pull-up optimal resistor (MS1,MS2,HKS pin) SDI pin input resistance Oscillator frequency Oscillator start time Common/Segment pins HKS pin input voltage HKS, MS1, MS2, input pin debouce time Crystal input and output pin built-in capacitor
Vi switch from VDD to VSS and Ri switch from RoiL to RoiH Vi = VSS VDD =1.3V
CO
-
20
-
pF
* This specification are subject to be changed without notice.
3.17.1999
14
LCD PANEL
SEG0 SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30 SEG31 COM0 COM1 COM2 COM3
DIALER PART VDD VDD
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
1M C945
C945 EXTRA 1.5V BATTERY VDD CALENDAR
OFF
58 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 SEG26 SEG25 SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 80
APPLICATION CIRCUIT
RECOMMAND CRICUIT : C945
EM32117 can used this cricuit replace extra battery . ( But if LCD PANEL's power consumption are too large , the extra battery still be needed. )
HKS VDD
56 55 SEG28 SEG29 SEG30 SEG31 COM0 COM1 COM2 COM3 ENCLND ENRTC 24/12
VSS HKS VDD VC2 VC1 MS2 SDI V3 V2 XOUT XIN
ON
57 SEG27
SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 SEG0 GF TEST
SPARE2 SPARE1 MS1
8 9 10 11 12 13 14 15 16 17 18 19
HK RTC
OFF
53 52 51 50 49 48 54
C945
1N4148 VDD HOUR SDI
46
470K
ON
EM32117
VDD GF
* This specification are subject to be changed without notice.
in Prelim
SDO
12
24
47
ary
35
34
28
27
38
33
32
37
36
30 31
32768
40
29
39
VDD HKS
SDI
0.1u
TEST Should let it OPEN or PULL to HIGH
0.1u 0.1u
NOTED :
MS1 ,MS2 adjust Time
GF JUMP : General Flag icon for LOGO ON/OFF CALENDAR JUMP : CALENDAR ON/OFF
MS2
MS1
16DIGITLCDDRIVERWITHCHECKTIMEFUNCTION
3.17.1999
RTC HOUR
JUMP : Real Time Clock ON/OFF JUMP : 24/12 format select
EM32117
15
EM32117
16DIGITLCDDRIVERWITHCHECKTIMEFUNCTION
PAD DIAGRAM
SEG10 SEG12 SEG13 SEG14 SEG11
ina relim P
SEG15 SEG16 SEG17 SEG19 SEG20 SEG18
ry
SEG22 SEG23 SEG24
66
80
79
78
77
76
75
74
73
72
71
SEG21
70
69
68
67
65
SEG25
58 57 56 55 54 53 SEG26 SEG27 SEG28 SEG29 SEG30 SEG31 COM0 COM1 COM2 COM3 ENCLNDB ENRTCB F24&12B 52 51 50 49 48 47 46
SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 SEG0 GF TEST
8 9 10 11 12 13 14 15 16 17 18 19 (0,0)
EM32117
27
28 29
30
31 32 33
34
35
36
37
38
39
40
SPARE2
SPARE1
VDD
Chip Size : 2450 x 2130 m Pad No. 8 9 10 11 12 13 14 15 16 17 18 19 27 28 29 30 31 32 33 34 35 36 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 SEG0 GF TEST SPARE2 SPARE1 MS1 MS2 SDI HKS V DD V2 V3 VC1 Symbol X -1093.3 -1093.3 -1093.3 -1093.3 -1093.3 -1093.3 -1093.3 -1093.3 -1093.3 -1093.3 -1108.3 -1108.3 -1083.1 -955.0 -823.4 -695.3 -569.3 -437.7 -311.7 -185.7 -59.7 68.5 Y 666.6 525.5 399.2 258.1 132.1 -9.0 -135.0 -276.1 -402.1 -543.1 -669.1 -795.1 -932.2 -932.2 -932.2 -932.2 -932.2 -932.2 -936.1 -936.1 -940.6 -936.1 3.17.1999
16
* This specification are subject to be changed without notice.
XOUT
MS1
HKS
VC1
VSS
MS2
VC2
XIN
SDI
V2
V3
EM32117
16DIGITLCDDRIVERWITHCHECKTIMEFUNCTION
in Prelim
Pad No. 37 38 39 40 46 47 48 49 50 51 52 53 54 55 56 57 58 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 Symbol VC2 V SS XIN XOUT 24/12 ENRTC ENCLND COM3 COM2 COM1 COM0 SEG31 SEG30 SEG29 SEG28 SEG27 SEG26 SEG25 SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 X
ary
Y -941.4 -931.3 -931.3 -935.2 -945.9 -819.9 -693.9 -552.2 -410.5 -284.5 -144.2 -18.2 122.9 248.9 390.0 516.0 657.1 929.6 929.6 929.6 929.6 929.6 929.6 929.6 929.6 929.6 929.6 929.6 929.6 929.6 929.6 929.6 929.6
196.6 322.6 448.6 621.6 1099.3 1099.3 1099.3 1089.8 1089.8 1089.8 1089.8 1089.8 1089.8 1089.8 1089.8 1089.8 1089.8 1081.7 929.5 788.3 661.3 520.2 380.2 210.6 72.3 -83.5 -221.8 -377.6 -512.5 -660.6 -788.4 -929.5 -1085.4
* This specification are subject to be changed without notice.
3.17.1999
17
EM32117
16DIGITLCDDRIVERWITHCHECKTIMEFUNCTION
ina relim P
12 DIGITS LCD PANEL DESIGN NOTE LCD Panel Description
ry
The 12 digits LCD display font of the EM32117 LCD driver is shown as the following :
Digit #
16
RD
15
SPEAKER
14
HOLD
13
12
MEMORY
11
10
9
ALARM
8
STORE
7
PAGE
6
5
AUTO
4
LOCK
3
SAVE
2
1
MUTE
LO BATT
4
5
6
7
8
9
0
*
#
PAUSE TONE DASH
COM3 COM2 COM1 COM0
SEG23 12f 12g 12e 12d SEG15 8f 8g 8e 8d SEG7 4f 4g 4e 4d
SEG22 12a 12b 12c RD SEG14 8a 8b 8c GF SEG6 4a 4b 4c AUTO
SEG21 11f 11g 11e 11d SEG13 7f 7g 7e 7d SEG5 3f 3g 3e 3d
SEG20 11a 11b 11c Speaker SEG12 7a 7b 7c ALARM SEG4 3a 3b 3c LOCK
SEG19 10f 10g 10e 10d SEG11 6f 6g 6e 6d SEG3 2f 2g 2e 2d
SEG18 10a 1b 10c HOLD SEG10 6a 6b 6c STORE SEG2 2a 2b 2c SAVE
SEG17 9f 9g 9e 9d SEG9 5f 5g 5e 5d SEG1 1f 1g 1e 1d
SEG16 9a 9b 9c Memory SEG8 5a 5b 5c PAGE SEG0 1a 1b 1c MUTE
COM3 COM2 COM1 COM0
COM3 COM2 COM1 COM0
RD
COM3 COM2 COM1 COM0
SPEAKER
HOLD
MEMORY
GF
ALARM
STORE
PAGE
AUTO
LOCK
SAVE
MUTE
* This specification are subject to be changed without notice.
3.17.1999
18
EM32117
16DIGITLCDDRIVERWITHCHECKTIMEFUNCTION
in Prelim
RD SPEAKER HOLD MEMORY GF ALARM STORE
ary
SAVE MUTE
PAGE AUTO LOCK
SEG23 SEG21
SEG19 SEG17 SEG15
SEG13 SEG11
SEG9
SEG7
SEG5
SEG3
SEG1 SEG0
SEG22 SEG20
SEG18 SEG16 SEG14
SEG12 SEG10
SEG8
SEG6
SEG4
SEG2
Figure 2 - Segment pin wiring diagram Driving a 12 digit LCD panel When the EM32117 is driving a 12 digit LCD panel, the ENCNLD should be pulled to VDD to suppress the display of calendar. For example, * When the system is in State 1 (the LCD panel is at RTC mode), pulling ENCNLD to VDD will disable display of calendar.
Note: Calendar display will be automatically suppressed when Real-Time Clock is disable (pulling ENRTC to high level).
* This specification are subject to be changed without notice.
3.17.1999
19
EM32117
16DIGITLCDDRIVERWITHCHECKTIMEFUNCTION
PAD DIAGRAM
SEG12 SEG13 SEG14 SEG15 SEG10 SEG11
ina relim P
SEG16 SEG17 SEG19 SEG20 SEG18
ry
SEG22 SEG23
SEG21
NC
66
80
79
78
77
76
75
74
73
72
71
70
69
68
67
65
NC
58 57 56 55 54 53 NC NC NC NC NC NC COM0 COM1 COM2 COM3 ENCLNDB ENRTCB F24&12B 52 51 50 49 48 47 46
SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 SEG0 GF TEST
8 9 10 11 12 13 14 15 16 17 18 19 (0,0)
EM32117
27
28 29
30
31 32 33
34
35
36
37
38
39
40
SPARE2
SPARE1
VDD
Chip Size : 2450 x 2130 m Pad No. 8 9 10 11 12 13 14 15 16 17 18 19 27 28 29 30 31 32 33 34 35 36 Symbol SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 SEG0 GF TEST SPARE2 SPARE1 MS1 MS2 SDI HKS VDD V2 V3 VC1 X -1093.3 -1093.3 -1093.3 -1093.3 -1093.3 -1093.3 -1093.3 -1093.3 -1093.3 -1093.3 -1108.3 -1108.3 -1083.1 -955.0 -823.4 -695.3 -569.3 -437.7 -311.7 -185.7 -59.7 68.5 Y 666.6 525.5 399.2 258.1 132.1 -9.0 -135.0 -276.1 -402.1 -543.1 -669.1 -795.1 -932.2 -932.2 -932.2 -932.2 -932.2 -932.2 -936.1 -936.1 -940.6 -936.1 3.17.1999
20
* This specification are subject to be changed without notice.
XOUT
MS1
HKS
VC1
VSS
MS2
VC2
XIN
SDI
V2
V3
EM32117
16DIGITLCDDRIVERWITHCHECKTIMEFUNCTION
in Prelim
Pad No. 37 38 39 40 46 47 48 49 50 51 52 53 54 55 56 57 58 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 Symbol VC2 Vss XIN XOUT 24/12 ENRTC ENCLND COM3 COM2 COM1 COM0 NC NC NC NC NC NC NC NC SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 X
ary
Y -941.4 -931.3 -931.3 -935.2 -945.9 -819.9 -693.9 -552.2 -410.5 -284.5 -144.2 -18.2 122.9 248.9 390.0 516.0 657.1 929.6 929.6 929.6 929.6 929.6 929.6 929.6 929.6 929.6 929.6 929.6 929.6 929.6 929.6 929.6 929.6
196.6 322.6 448.6 621.6 1099.3 1099.3 1099.3 1089.8 1089.8 1089.8 1089.8 1089.8 1089.8 1089.8 1089.8 1089.8 1089.8 1081.7 929.5 788.3 661.3 520.2 380.2 210.6 72.3 -83.5 -221.8 -377.6 -512.5 -660.6 -788.4 -929.5 -1085.4
* This specification are subject to be changed without notice.
3.17.1999
21

▲Up To Search▲

Price & Availability of EM32117Q

	To Download EM32117Q Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .